What Makes a MEMS Foundry Different From a Regular Chip Foundry?
Author : crystal webster | Published On : 20 Nov 2026
Nadia spent years designing circuits. Then she joined a team building a tiny gyroscope and walked into her first meeting about the fab. People kept saying “release,” “cavity” and “seal.” She nodded politely and understood almost none of it. Afterward she asked the quiet question: why can’t any chip foundry just make this? That question is the heart of what a MEMS foundry does differently.
Short version: MEMS parts move, flex or hold gas, so the factory flow has to carve and seal things, not just layer and wire them. InchFab’s pages describe a platform built for exactly that kind of work. Let’s go through the differences in plain words, and what you should ask before choosing a partner.
Why Don’t Moving Parts Fit a Normal Flow?
A regular circuit is mostly flat layers and wires. A MEMS device has parts that must bend, spin or vibrate, which means material has to be removed underneath them. Empty space is part of the design. A flow made only for flat layers simply doesn’t have the steps to create that space, however good its other tools are.
Think of a drum. The skin only works because air sits behind it. Take away the air and you’ve got a piece of rubber glued to a block. MEMS sensors lean on similar ideas, with membranes, beams and gaps. So the factory must know how to build the gap, not only the skin on top of it.
What Tools Build the Gap?
InchFab’s line lists DRIE, RIE oxide and RIE nitride in a dry etch module with up to 4 chambers, and the Foundry Service page names Bosch DRIE. Deep etching is how many MEMS cavities and trenches get made. The pages also list acid and solvent stations for wet steps, which handle other kinds of material removal and cleaning.
Bonding closes the loop. The line lists aligned wafer bonding by anodic, fusion and thermal compression methods, which can seal a cavity between two wafers. Combine deep etching with bonding and you can make hollow, sealed devices. That pairing is a big reason a MEMS foundry looks so different from a plain logic one.
What Does InchFab Say It Builds?
The standard process list on the Foundry Service page includes vacuum getters, microfluidics, microlenses, pressure sensors, silicon micro molds, nano imprint hardmasks and optical coatings with gratings. Several of those lean on MEMS style steps like cavities and sealed chambers. If your idea sits close to one of them, you might start with a path that already exists.
Under MEMS and Sensors, the page lists pressure sensors, inertial sensors, MEMS microphones, humidity and gas sensors, temperature sensors, flow sensors, magnetic sensors, tactile sensors, optical MEMS, resonators, strain gauges and chemical sensors. It’s a wide menu. The pages give no performance numbers, though, so ask the team for data before you plan around any of them.
How Does a Custom MEMS Flow Work Here?
The Foundry Service page says InchFab develops processes from scratch or adapts existing flows, with no need to conform to a standard one. For MEMS that matters a lot, since few devices share an identical recipe. A gyroscope and a gas sensor need different etches, films and seals, even when they sit on the same wafer size.
Wafers are 100mm on the InchFab Line page. That’s small, which suits prototypes and moderate volumes. If your design needs bigger wafers, raise it right away. Fit is a practical question, and an early no is much kinder than a late one that arrives after you’ve paid for masks.
How Should You Choose a MEMS Foundry?
Start with your device and ask three things: which steps carve and seal it, which tools handle those steps, and who has built something similar. When you compare any MEMS foundry on your list, a team that answers in specifics beats one that recites a brochure. Every single time, honestly.
Next, ask about speed and cost. InchFab says early development turnaround can be as fast as one week, and that volume cost per chip holds up against traditional 200mm to 300mm foundries. Those are company claims, so ask what each one assumes. Also ask what happens when a step fails halfway through a run.
What Should You Send First?
Send a drawing of the device, a rough layer stack, wafer size, quantity and target date. Say which parts move and which are sealed. Mention any fragile features. Use the Get a Process Quote button on the Foundry Service page, or write to . The more detail you give, the more useful the first reply will be.
Nadia’s first note was a single paragraph and a sketch. The reply asked about her cavity depth and how she planned to seal it, which told her the team knew the territory. A good question coming back at you is often the best sign you’ll get before any wafer runs.
What Mistakes Do Newcomers Make?
Teams forget to mention sealed cavities, pack devices too tightly, skip test structures and assume packaging will sort itself out. All four are avoidable. The Foundry Service page lists process monitor chips and test structures, plus packaging options like wafer level chip scale packages and through silicon vias, so bring them up early.
Another classic: changing three things at once, then not knowing which one broke the device. Change one variable per run when you can. It feels slow, and it’s actually faster in the long run. A calm, boring experiment plan beats a clever, tangled one almost every time.
So, What’s the Real Difference?
A MEMS foundry has to carve, release and seal, not only layer and wire. That takes process development services deep etching, careful films, bonding and a team that understands moving parts. InchFab’s pages list tools and processes aimed at that kind of work, though the details need confirming for your own design and your own numbers.
Nadia now sits in those meetings and uses the words without blinking. If you’re new to MEMS, learn the handful of terms, ask blunt questions and share your drawing early. Everything else gets easier once the factory understands what your device really needs.
FAQs
Does InchFab list DRIE?
Yes. The InchFab Line page lists DRIE and the Foundry Service page lists Bosch DRIE.
Is wafer bonding available?
The InchFab Line page lists aligned wafer bonding by anodic, fusion and thermal compression methods.
Which MEMS devices are listed?
Pressure, inertial, humidity, gas, temperature, flow, magnetic and tactile sensors, microphones, optical MEMS, resonators, strain gauges and chemical sensors.
What wafer size is used?
The InchFab Line page lists 100mm, or 4 inch, wafers.
