Ward Leonard Method of Speed Control of DC Motors: Working, Advantages, and Applications

Author : nvistech nvistech | Published On : 18 Nov 2026

TL;DR

  1. Engineering students and competitive exam aspirants who find DC motor speed control confusing will learn how the Ward Leonard system works, why it was adopted, and how to solve speed and power problems on it.

  2. Speeds below base speed are varied smoothly by changing the generator field, which sets the armature voltage of the motor from zero up to its rated value.

  3. Speeds above base speed are obtained by weakening the motor field flux. Torque falls in this region while power stays roughly constant.

  4. Reversing the generator field polarity reverses the motor, and the arrangement can return energy during braking.

  5. The three rotating machines make the classical set costly, heavy, and inefficient at light load, so static thyristor drives have replaced it in most new installations, though the principle remains central to DC drive theory.

Introduction

The Ward Leonard method is a technique for controlling the speed of a DC motor by changing the voltage applied to its armature. The variable voltage comes from a separately excited DC generator, which is driven by a prime mover running at nearly constant speed. Harry Ward Leonard introduced this arrangement in 1891, and it served as the standard approach for demanding drives long before solid-state converters appeared around 1960.

The method sits at the centre of DC motor speed control theory. Students meet it in electrical machines courses and in competitive exam syllabi, and the same armature voltage principle still underlies modern thyristor-based DC drives. The rotating motor-generator set has been replaced in most new plants, but the reasoning behind it has not changed.

This article covers the speed equation that governs the method, the working of the generator and motor arrangement, the two control regions, reversal and braking, the advantages and disadvantages, a worked numerical example, and the exam and industrial context relevant to Indian readers.

Fundamentals: What Determines the Speed of a DC Motor

A DC motor develops a back emf in its armature that opposes the applied voltage. In steady operation, the back emf equals the armature terminal voltage minus the drop across the armature circuit. Because the back emf is proportional to flux and speed, the speed can be written as

N = (Vₜ − Iₐ Rₐ) / (K φ)

Here N is the speed in rpm, Vₜ is the armature terminal voltage in volts, Iₐ is the armature current in amperes, Rₐ is the total armature circuit resistance in ohms, φ is the flux per pole in webers, and K is a machine constant that depends on the winding and construction.

The equation shows that speed can be changed in three ways: by altering the resistance in the armature circuit, by altering the flux, or by altering the terminal voltage. Each route has a different effect on efficiency and torque, and each suits a different kind of drive.

The armature resistance method is simple but wasteful. The inserted resistor converts electrical power into heat in proportion to the square of the armature current, and speed also drops sharply as load increases. Field control is efficient, but it can only raise speed above the rated value, and the increase is limited because a weaker flux affects commutation. Armature voltage control avoids both problems. It keeps the flux at its rated value, lowers the speed in proportion to the applied voltage, and dissipates little power in the control path. The difficulty was that a continuously variable DC supply was not readily available when this method was first needed. The Ward Leonard speed control method solved exactly that problem.

Origin of the Ward Leonard Control System

Harry Ward Leonard developed the arrangement in 1891. Some textbooks give only the 1890s as the period, but the 1891 date is the one most commonly cited. Before this system, the usual way to reduce speed was to insert resistance in series with the armature. That approach throws away energy and gives poor speed regulation.

Leonard's idea was to generate a variable DC voltage with a dedicated generator and feed that voltage to the motor. The motor keeps a fixed field, and the generator does the work of speed control. This separation of duties is the core of the Ward Leonard control system, and it explains why the arrangement has three machines instead of one.

How the Ward Leonard System Works

The Ward Leonard system of speed control uses three electrical machines and a small control circuit. The prime mover runs the generator at roughly constant speed. A three-phase induction motor or a synchronous motor is the common choice, though a DC motor or an engine can serve the same role. The separately excited DC generator converts this mechanical input into a DC output whose voltage depends on its own field current. The generator output feeds the armature of the DC motor being controlled, and the motor has its own field supply, which is held at its rated value during speed control.

A field regulator in the generator circuit sets the generator field current. The generator EMF rises with that current, so the voltage at the motor terminals can be raised smoothly from zero to its rated value. The motor speed follows this terminal voltage. Because the generator field current is small compared with the armature current it supplies, the control effort is modest even for large drives.

This design gives a single control point for the whole low speed range. Changing one field current adjusts the speed continuously, without the steps that a multi-tap resistor produces.

The Two Control Regions

The Ward Leonard system operates in two distinct regions, separated by the base speed, which is the rated speed of the motor at rated flux and rated voltage. The behaviour in each region follows directly from the speed equation.

Below Base Speed: Armature Voltage Control

Below base speed, the motor field stays at its rated value, so the flux φ remains constant. The generator voltage is reduced, which lowers the motor terminal voltage Vₜ. The armature current is held at its rated value. Torque is proportional to flux multiplied by armature current, so with both quantities fixed, the torque stays at its maximum rated value regardless of speed. This is the constant torque region.

Speed rises in direct proportion to the terminal voltage in this region. Power, however, falls as speed falls, because power equals torque multiplied by angular speed, and the torque is fixed. A drive that is run at half rated speed therefore delivers about half its rated power when it carries rated current.

Above Base Speed: Field Control

Above base speed, the armature terminal voltage is kept at its rated value and the motor field current is reduced. Weakening the flux raises the speed, since the back emf must still balance the applied voltage. The motor can then run faster than its rated value, but its torque drops in proportion to the flux, because torque depends on φ and Iₐ.

The power in this region stays roughly constant. The back emf stays close to the applied voltage, so the product of back emf and armature current remains near its rated value. This is the constant power region. Speed in this region is limited by commutation problems and mechanical considerations, which is why an overspeed protection device is normally fitted on such drives.

Reversing the Motor and Braking the Load

Reversing the direction of rotation requires no change to the motor itself. Reversing the polarity of the generator output reverses the armature voltage, and with it the direction of rotation. This is achieved by reversing the generator field current. The motor-generator set keeps turning in its original direction, so the change is quick and uncomplicated.

Braking follows the same logic. When the motor must slow down quickly, the generator voltage is reduced below the back emf. The motor then acts as a generator and feeds energy back through the system. Whether that energy is returned to the supply or absorbed depends on how the generator, prime mover, and supply are designed. Where the arrangement can return energy, the system performs regenerative braking, which saves energy during repeated stop and start cycles, such as lifting and lowering loads in a hoist.

Advantages of the Ward Leonard Method

The most important advantage is smooth speed control from zero up to base speed. Because the motor speed follows the generator voltage, the adjustment can be fine and continuous. Operators and automatic controllers both benefit from this, which is why the method was chosen for precise positioning and for loads whose speed must change frequently.

The system also gives a wide speed range. Armature voltage control covers the range below base speed, and field control extends it above base speed, so a single arrangement serves both regions. Reversal and braking are straightforward, as described earlier, and the regenerative capability adds efficiency during braking.

Acceleration and deceleration can be controlled by ramping the generator field current, which keeps the motor current within safe limits during transients. Speed regulation is good, and closed-loop feedback can keep the speed steady as the load changes, compensating for drops that depend on load. Finally, because no large series resistor sits in the armature circuit, the control path avoids the heavy power loss that marks the resistance method.

Disadvantages of the Ward Leonard Method

The main drawback is cost. A complete set requires three rotating machines, namely the prime mover, the generator, and the motor, and textbook treatments note that each Ward Leonard drive needed machines of similar power rating. Buying, installing, and housing three large machines is expensive, which is why the arrangement was reserved for applications that truly needed its performance.

Efficiency is the second concern. Losses occur in all three machines, including friction, windage, iron, and brush losses. At light load, these fixed losses form a large share of the input, so the overall efficiency falls sharply. The set is also large and heavy, needs substantial floor area, and requires regular maintenance of commutators, brushes, bearings, and cooling systems. Rotating machines of this size produce more noise and vibration than a modern electronic drive. The response to rapid changes in command is slower as well, because the generator field and the rotating inertia both limit how quickly the speed can change.

Worked Example: Speed and Power in the Two Regions

The following problem shows how both regions can be checked numerically. It follows the style of GATE EE and SSC JE electrical machine questions, and each step is shown so the method can be repeated independently. Losses, armature reaction, and generator voltage drops are neglected throughout.

A separately excited DC motor is rated at 220 V. Its armature resistance is 0.5 Ω, its rated armature current is 20 A, and its rated speed is 1000 rpm at rated flux. The motor is driven by a Ward Leonard system and runs at rated armature current. The problem asks for three results: (a) the generator output voltage needed for 500 rpm with full flux, (b) the flux ratio needed for 1500 rpm when the generator output is held at 220 V, and (c) the output power and torque at 1500 rpm.

Step 1: Find the back emf at the rated operating point.

E_b = Vₜ − Iₐ Rₐ = 220 − (20 × 0.5) = 220 − 10 = 210 V

Step 2: Find the speed constant at rated flux.

Kφ = E_b / N = 210 / 1000 = 0.21 V per rpm

Step 3: Solve part (a). At 500 rpm with full flux, the back emf is

E_b = 0.21 × 500 = 105 V

The armature terminal voltage must then be

Vₜ = E_b + Iₐ Rₐ = 105 + (20 × 0.5) = 115 V

The generator must therefore supply 115 V. As a check, the output power at this speed is E_b × Iₐ = 105 × 20 = 2100 W, which is half the rated power of 4200 W. This matches the constant torque behaviour below base speed.

Step 4: Solve part (b). The generator output is held at 220 V, so the terminal voltage stays at 220 V. The armature current is still 20 A, so the back emf is still 210 V. At 1500 rpm,

Kφ′ = 210 / 1500 = 0.14 V per rpm

The flux ratio is therefore

φ′ / φ = 0.14 / 0.21 = 0.667

The motor must operate at about two thirds of its rated flux to reach 1500 rpm.

Step 5: Solve part (c). The output power at 1500 rpm is

P = E_b × Iₐ = 210 × 20 = 4200 W = 4.2 kW

The angular speed is ω = 2π × 1500 / 60 = 157.1 rad/s, so the torque is

T = P / ω = 4200 / 157.1 = 26.7 N·m

For comparison, the rated torque at 1000 rpm is 4200 / 104.7 = 40.1 N·m. The ratio 26.7 / 40.1 = 0.667 matches the flux ratio from Step 4, which confirms the reduction in torque.

The result shows the two regions clearly. At 1500 rpm the power equals the rated 4.2 kW, while the torque has fallen to two thirds of its rated value. This is the constant power behaviour of field control. Had the same motor been run at 500 rpm, the power would have been 2.1 kW, half of its rated value, reflecting the constant torque region below base speed. Students who can reproduce each of these steps with a different rated current or speed are well prepared for this type of question.

Applications of the Ward Leonard System

The method found its place wherever smooth low speed operation, reversal, braking, and a wide speed range were needed together. Historical installations include colliery winders, mine hoists, cranes, excavators, elevators, rolling mills, paper machines, and diesel-electric locomotives. Steelworks were particularly heavy users. A large plant could contain a room full of motor-generator sets, one for each variable speed motor, which shows how much equipment a single drive could require.

The reasons for these choices are practical. A hoist must lower a heavy load smoothly, reverse direction, and recover energy when the load descends. A rolling mill must hold a precise speed through changing loads. The Ward Leonard arrangement handled these demands well, even though its equipment cost was high.

How the Ward Leonard Method Compares with Other Speed Control Methods

The table below compares the three classical speed control methods for a separately excited DC motor. The Ward Leonard system appears in the last row because it combines armature voltage control below base speed with field control above it.

Method

Quantity varied

Speed range covered

Efficiency

Main drawback

Armature resistance control

Resistance in the armature circuit

Below base speed

Low, since power is lost as heat in the resistor

Large losses and poor speed regulation with load

Field flux control

Motor field current

Above base speed

Good

Speed limit set by commutation, and torque falls as flux falls

Armature voltage control (Ward Leonard)

Armature terminal voltage from a variable supply

Zero to base speed, with field control above base

Good for the motor, though the rotating set adds its own losses

Cost, size, maintenance, and poor light-load efficiency of the set

The table makes one point clear. The Ward Leonard method is not an alternative to field control. It uses armature voltage control as its main tool and adds field control to reach higher speeds.

Thyristor converters now perform the same function as the rotating generator in most new drives. A controlled rectifier fed from the AC mains through a transformer supplies the variable DC voltage, with its output set by the firing angle of the thyristors. This removes the prime mover and the generator, and it produces a smaller, quieter drive with faster response. The price is that thyristor rectifiers draw harmonic currents from the supply, so filtering and careful design are necessary. The motor's own brushes and commutator remain, so maintenance is reduced rather than eliminated. Field control of the motor still applies in the static version, so the two-region behaviour of the Ward Leonard system carries over unchanged.

India-Specific Context

Steel plants and material handling are the Indian sectors where this topic carries the most practical weight. The shift from rotating sets to static control is visible in engineering standards used by the Indian steel industry. The inter plant standard IPSS:1-10-018-03, for example, covers hoist motor control schemes that use thyristors for AC cranes. Such standards show how plant specifications have moved toward static control.

I could not verify, from the sources available for this article, which Indian plants still operate rotating Ward Leonard sets or which public sector undertakings use them today. For that reason, this article does not name any specific installation. Candidates preparing for interviews at public sector units should instead be ready to explain the working principle, the two control regions, and the reasons thyristor drives replaced the rotating sets.

Exam Relevance by Paper

The relevance of this topic depends on the paper, so candidates should plan their preparation accordingly.

For GATE Electrical Engineering, speed control of DC motors is part of the electrical machines syllabus. Questions that combine armature voltage control and field control appear in GATE EE practice material and sample papers. A typical problem asks the candidate to compare the output power of a shunt motor driven at half rated speed by armature voltage control with its output at one and a half times rated speed by field control. The answer follows from the constant torque and constant power reasoning used in the worked example, so the concept must be understood rather than memorised.

For GATE Electronics and Communication Engineering, this topic falls outside the syllabus, so ECE aspirants need not study it in depth.

For SSC JE, the Electrical Paper II syllabus includes DC machines, their characteristics, and the speed control and starting methods of DC motors. The Ward Leonard system is one of the standard speed control methods within that topic, so candidates should be able to describe its working and compare it with resistance control and field control. Candidates should confirm the current syllabus in the official SSC notification before they begin revision.

For RRB JE, the electrical syllabus should be checked directly in the official notification. This article did not verify the current RRB JE electrical syllabus, so no specific claim about it is made here.

Conclusion

The Ward Leonard method earned its place by solving a real engineering problem: how to change the speed of a DC motor smoothly, reverse it, and brake it without wasting energy in resistors. The working principle is straightforward once the speed equation is clear. Armature voltage sets the speed below base value at constant torque, and field weakening sets the speed above base value at constant power. Rotating sets have largely given way to thyristor drives, yet the same two regions govern the static versions.

A reader who can derive the numbers in the worked example, and explain why power stays constant in the field control region, will be well placed for GATE and SSC JE questions on DC drives. A useful next step is to change the rated current in the example to 15 A, repeat each calculation, and then attempt previous year electrical machine questions on speed control from official exam papers. Working through several such problems tends to reveal the difference between knowing the formulas and understanding the drive.

Frequently Asked Questions

Q: Why is the Ward Leonard method preferred over armature resistance control?

Armature resistance control dissipates power as heat in the series resistor, and its speed changes sharply with load. The Ward Leonard method avoids that loss in the control path, and it keeps the speed steadier as the load varies. The trade-off is the cost and maintenance of the rotating set, which is why the method was chosen only where its performance was genuinely needed.

Q: Can the Ward Leonard speed control method give speeds above the rated speed?

Yes. Once the armature voltage reaches its rated value, the motor field is weakened to raise the speed further. Torque falls in this region, while power stays roughly constant. Commutation limits and mechanical considerations restrict how high the speed can go, so overspeed protection is normally provided.

Q: How is the direction of rotation reversed in a Ward Leonard drive?

The direction is reversed by changing the polarity of the generator output, which is done by reversing the generator field current. This reverses the armature voltage of the motor. The motor and the prime mover continue to run in their original directions, so the reversal is fast and needs no switching of the motor's own connections.

Q: Is the Ward Leonard method still used in industry?

Most new installations use thyristor or other static converters in place of rotating motor-generator sets. Some existing installations keep the set and modernise its control. The armature voltage principle remains the basis of static DC drive design, so the method is still important to study even where the hardware has changed.

Q: Is the Ward Leonard method the same as armature voltage control?

Not quite. Armature voltage control is the principle, which means varying the voltage across the armature to change speed. The Ward Leonard system is one practical way to supply that variable voltage, using a separately excited generator. Thyristor converters are another. So the Ward Leonard system is an implementation of armature voltage control rather than a separate principle.

Q: Which topics should GATE EE and SSC JE candidates study alongside this method?

Candidates should cover the speed and torque equations of DC motors, the constant torque and constant power regions, the other speed control methods, starting and braking of DC motors, and the losses and efficiency of DC machines. These topics are grouped together in the electrical machines syllabus, and questions on one often draw on the others.