Clutch Friction Disc Material: How to Choose the Right Facing for Torque, Heat and Durability

Author : protec friction | Published On : 19 Nov 2026

ProTec Friction Group offers a wide range of clutch friction materials, including organic, woven, Kevlar, sintered and carbon options. Each material delivers different friction, heat resistance, durability and burst strength. Choosing the right facing ensures smooth engagement, reliable torque transmission and longer clutch service life.

wet-friction-plates-parts-1

A clutch has a deceptively simple job: connect and disconnect power smoothly, transmit torque without slipping and do it again thousands of times. Whether the clutch sits in a heavy truck, a race car, an agricultural machine or an industrial press, the Clutch Friction Disc Material determines how well it performs that job and how long it lasts.

ProTec Friction Group supplies clutch facing materials and friction components for automotive, heavy truck, motorsport and industrial applications. This guide compares the main Types of Clutch Disk Friction Material in ProTec's range, explains the properties that matter most and offers a practical framework for choosing the right facing.

What a Clutch Facing Must Deliver

Clutch facings face a demanding combination of conditions. They must grip firmly enough to transmit torque, engage smoothly to avoid shock and judder, survive repeated heat cycles and stay physically intact at high rotational speeds. The key properties to compare are:

• Friction coefficient, both static and dynamic, which affects torque capacity and engagement feel

• Thermal limits, including continuous and intermittent operating temperatures and fade temperature

• Wear rate, which drives service life

• Burst resistance, the speed a facing can withstand before failing structurally

• Mating surface compatibility, since the facing works as a pair with its pressure plate or flywheel

ProTec publishes many of these values on its product datasheets, measured under specific test conditions, and notes that results can vary in different applications.

Organic and Woven Clutch Facing Materials

TF2000 Organic Clutch Facing Material

TF2000 is an organic clutch friction material reinforced with glass fiber yarn, spiral woven with a fine copper core. ProTec lists automotive clutches, light truck clutches and many types of industrial clutches among its applications. Published data includes:

• Static friction coefficient: 0.55 ± 0.05 (as supplied) and 0.60 ± 0.05 at 100°C

• Dynamic friction coefficient: 0.55 ± 0.05

• Wear rate: 70 ± 10 mm³/kWh at 150°C

• Fade temperature: above 300°C

• Burst resistance: 6,500 ± 100 RPM at 200°C

TF2016 Aramid Clutch Facing Material

TF2016 is a woven, rigid friction material made with draft yarn and aramid fibers, also listed as "Kevlar Clutch Friction." ProTec recommends it for commercial vehicles, especially where thermal conditions are high. Its listed applications include heavy-duty automotive clutches, heavy truck clutches and many industrial clutches. Published data includes:

• Static friction coefficient: 0.53 ± 0.05 (as received) and 0.55 ± 0.05 at 100°C

• Dynamic friction coefficient: 0.50 ± 0.05

• Wear rate: 30 mm³/kWh at 150°C

• Burst resistance: 12,000 ± 100 RPM at 200°C

Its notably low wear rate and high burst resistance make it a strong candidate for demanding commercial duty.

TF2025 Organic Metallic Clutch Material

TF2025 is a woven material with glass fiber reinforcement yarn spiral-woven around a fine copper core and reinforced with extra copper. Its static and dynamic coefficients are both listed at 0.45 ± 0.05, with a wear rate of 35 ± 10 mm³/kWh at 150°C, a fade temperature above 400°C and burst resistance of 6,500 ± 100 RPM. Listed applications include heavy-duty automotive clutches, heavy truck clutches and industrial clutches.

Why Glass Fiber and Copper Matter

ProTec's article on clutch components explains that glass fiber reinforcement in clutch facings improves heat dissipation, strength, wear resistance and resistance to deformation. TF2000 and TF2025 both combine glass fiber yarn with a fine copper core, and TF2025 adds extra copper reinforcement.

Kevlar and Paper Friction Materials

TF1600 High Kevlar Friction Material

TF1600 is a non-metallic paper friction material with a significant percentage of Kevlar (aramid) fiber. Its applications include high-performance car and motorcycle clutches, clutch buttons, heavy vehicle clutches and industrial clutches. ProTec notes that it usually needs no backing plate for clutch applications and is claimed to eliminate the break-in period common to other high-aramid materials.

Published values include a dynamic coefficient of 0.40 ± 0.05, a maximum continuous operating temperature of 360°C, a fade temperature above 400°C and burst resistance of 18,200 ± 100 RPM at 200°C. It is suitable for both dry and oil-immersed use.

In ProTec's high-speed stamping press case study, clutch-brake supplier Goizper selected TF1600 for its clutch-brakes and flywheel assemblies. ProTec reports that clutch service life was extended four to six times over previous solutions, even at higher cycle speeds.

TF1700 High Kevlar Metallic Friction Material

For higher friction, TF1700 adds metallic content to a Kevlar paper base. It lists a dynamic coefficient of 0.65 ± 0.05 and a fade temperature above 500°C, with applications including high-performance motorsport clutches, clutch rings and buttons, and extreme-duty industrial and off-road clutches.

Sintered and Carbon Materials for Wet Clutches

Some clutches run immersed in oil. ProTec's wet friction white paper explains that oil carries heat away but typically gives lower friction coefficients, so wet clutches need materials formulated for that environment.

•TT131 sintered bronze lists differential clutches, high-load clutches and wet-running applications. ProTec describes a stable friction coefficient under high load and friction stability in high-performance oils. Oil grooves can be pressed or machined.

• TTC141 carbon friction material lists transmission clutches and limited-slip differentials. It has a static-to-dynamic ratio close to 1:1, which ProTec links to smooth engagement and good noise, vibration and harshness performance.

ProTec's wet friction white paper also notes that groove patterns matter: spiral or radial grooves move large volumes of oil for cooling, while concentric grooves help hold oil at the interface for smoother engagement.

Facing Attachment: Rivets and Bonding

A great clutch disk friction material still needs to stay attached. ProTec's white paper on tubular rivets explains that the rivet joint between the friction lining and core plate must resist shear and tensile forces from torque transmission and vibration. It argues that tubular rivets offer lower mass, which reduces driven disc inertia and synchronizer work, along with a hollow bore that helps evacuate debris and vent heat.

Bonding is the other option. ProTec's clutch components article describes a facing adhesive designed to resist heat and prevent delamination, and notes that in friction systems, failure is often adhesive rather than mechanical. ProTec's datasheets generally recommend a thermosetting adhesive, and its bonding service offers both hot and cold bonding.

Choosing the Right Clutch Friction Disc Material

Use these questions to narrow the choice:

1. How much torque must the clutch carry? Higher friction materials such as TF1700 allow more torque for the same clamping force.

2. How hot will it run? For high thermal loads, look at materials such as TF2016, which ProTec recommends where thermal conditions are high.

3. Is it dry or wet? Wet clutches suit materials such as TT131 and TTC141, or TF1600, which works both dry and oil-immersed.

4. How fast does it spin? Compare burst resistance values.

5. What matters most: engagement feel, durability or cost? ProTec's motorsports page describes high-end organic materials as offering good cold bite and low noise and judder, while its Kevlar, ceramic and sintered options target higher temperatures and longer life.

Frequently Asked Questions

Which ProTec clutch material has the highest published burst resistance?

TF1600 lists burst resistance of 18,200 ± 100 RPM at 200°C.

What mating surface is recommended for ProTec clutch facings?

TF2000, TF2016 and TF2025 all list pearlitic cast iron, HB 150 to 200.

Can ProTec supply facings in custom shapes?

Yes. ProTec's clutch materials are offered in forms such as rings, gears, blocks, bonded parts and sheets.

Conclusion

The right clutch friction disc material depends on torque, heat, speed and environment. ProTec's range spans organic and woven facings such as TF2000, TF2016 and TF2025, Kevlar paper materials such as TF1600 and TF1700, and sintered and carbon materials for wet clutches. Comparing published friction, wear, thermal and burst data, then matching the facing to its mating surface and attachment method, gives every clutch the best chance of smooth engagement and long service life.

Find the Right Clutch Facing With ProTec

Specifying a new clutch or upgrading a facing that wears too quickly? ProTec's engineers can compare materials against your torque, temperature and duty cycle and supply facings in the shape you need.

• Call: +1 914-244-3600

• Email: [email protected]

• Corporate Office: 827 State Route 82, Suite 10-226, Hopewell Junction, NY 12533, USA

• Online: Contact the robotics team through protecfriction.com

Ask for datasheets, samples or a custom formulation, and give your clutch the facing it needs to perform.