butan agency

Author : amir yy | Published On : 16 Mar 2024

To carry out Bhutan package repairs with the phone number of Bhutan services in East Tehran

09191212489

Call .

Repairs are done by Bhutan package specialist as soon as possible.

 

By reading this article, you will learn about Bhutan package.

Butane package filling valve and its function

What is the identification of the butane package or manometer?

Whenever the package pressure drops, adjust it yourself and solve the package problem. (Common and identical in all packages)

What happens in the butane package if the gas package is disconnected?

How to reset the digital and analog packages of Bhutan?

Learn how to ventilate radiators correctly

Can the package burst? What are the risks of the package?

What should we do to make the package last longer?

How to recognize the errors of Bhutan package?

Training to work with the beta package as an example of Bhutan packages

 

I will explain the first three items together

Butane filling valve and what you need to know about it –

Manometer package

Adjusting the pressure of the butane package

Package faucet is the first part that is important for consumers to be familiar with

One of the things that often cause problems in the butane package is the pressure drop of the device
[that is, the package is working without water], which in most cases can be easily solved by opening the butane package filling valve and adjusting the pressure dial.

Below you can see two examples of filling valves

In the first photo, the filling valve is not installed

And the second photo is the filling valve on the installation package

In all packages of every model, the filling valve is almost the same with a slight difference.

For example, the plastic part of the filling valve may be black. It may be the filling valve on the left or right side of the package

The next part that you need to be familiar with is the package hand

You can see the picture of the load pressure hand

In the rest of the packages, the bar gauge or manometer is the same shape, when the bar is between 1 and 2, the package has no bar problem and Ali Al-Qaeda should work properly. Unless there is another problem, it is better that the load is between one and a half to 2.

The method of adjusting the load pressure of the butane package:

First, turn the filling valve of the butane package a few times.
Look at the manometer needle until it is in the one to two area.
Pay attention. At this stage, your hand must be on the filling valve. As soon as the needle is approaching 1/5, close the needle.

until the hand stops at one and a half or close to two

Then close the filling valve,
in 98% of cases, the butane package pressure problem will be solved and the package will turn on.

If it still does not turn on. Reset the package

Important note: Be sure to close the filling valve at the end of the work

Note: Some owners of wall-mounted packages have a habit of immediately opening the filler valve in case of any kind of damage to the package and expect the package to be fixed. Of course, it is not a big problem if you open the filling valve several times, but your expectation to make the package is wrong by doing so (so it is better to open the filling valve only when the pressure of the package drops)

Some friends also think that the higher the needle of the package goes, the higher the temperature of the water or the temperature of the heater, if there is no direct connection between the rising of the needle and the temperature of the radiators and the water used.
Just like if your car has more gas, it won't go faster or have more power. it's true ???

Pay attention to these points about the butane filling valve

If the water pressure of your unit is too low, you should adjust the load pressure at the end of the night or early in the morning

If the needle goes more than 2 bar, drain a little water from the air intake part of one of the radiators until the pressure becomes normal, i.e. below 2 bar.

Whatever you believe, opening the filler valve is not called ventilation, it is not, and it has nothing to do with ventilation. It is called package pressure adjustment.

What happens when the package gas is cut off and what should we do?

When the gas is cut off, the package tries to light the flame, but when it does not receive the command to light the flame. As a result, the package feels dangerous and gets locked. Here, if you are sure that the gas has been reconnected, you must reset the package to find the package again

Here, I teach how to reset two models of Bhutan's analog and digital packages

Steps to reset Calda Venezia and Optima package:

Find the volume button: This button is usually located in the middle of the package's control panel.

Put the button on standby mode: Turn it to standby mode by pressing the volume button.

Wait a few moments: After putting the button in standby mode, wait a few moments (about 5 seconds).

Switch the knob to winter or summer mode: Turn the volume knob to switch to winter ( ) or summer ( ) mode.

The package has been reset: By doing these steps, your package will be completely reset.

Resetting the Butane package of the Perla Perla Pro Perla Verona model. Beta and...

Steps to reset the package:

Find the key or volume corresponding to low and high volume of heating temperature. This key is usually located on the right side of the package screen.

Turn the key to the off position.

Wait a few seconds.

Turn the switch back to summer or winter mode.

Your Bhutan package has been reset.

How to ventilate the radiator at home

To vent the radiators, first turn off the heating system.

Then, using a vent wrench or screwdriver, loosen the radiator vent screw. Keep the screw open until you hear air escaping. After the air is out, close the screw.

Note that during venting, water may escape from the radiator. Therefore, place a container under the radiator.

 

 

After venting, go to the heating system and check its pressure. If the pressure of the heating system is less than 1 bar, open the filling valve until the pressure of the heating system reaches 1 to 1.5 bar.

Pay attention that this step must be repeated for each radiator and venting one radiator is not enough

There is an automatic air intake in the package that only drains the air inside the package, and the radiator air must be taken from time to time.

If there is no air in the radiator and water comes out, don't insist on emptying the water, there is no point

By following these tips, you can easily ventilate your home's radiators

Is it possible for the package to burst?

The question of whether the package (whether butane or butane or any other package) has the possibility of bursting or exploding is mostly asked by women,
of course the general answer is no. It is just as likely that a package will burst. But the package is not that safe.
First of all, I would like to say that if your package is in the balcony, the risks of the package will be much less, but what risks might the package have? And what should we pay attention to?

The danger of flooding the house,
as I said, it is very important to close the water valve, if you forget to close it, the device's safety valve may operate due to the increase in water pressure, especially at night, and start to supply water from the back of the package. This is the most important (the most frequent). There is a point that you should pay attention to regarding the risks of the package, because the cases of house flooding are relatively higher than other risks.

Gas leakage and fire
The risk of gas leakage in the package is the same as other gas-burning appliances such as heaters, stoves, or water heaters, but the safety of the package is much higher than other gas-burning appliances in terms of gas, so if the connections, hoses and gas package are tight, there is no other risk.

Risk of smoke leakage

During these last years, packages without fans became extinct, and all the models of the Bhutan package are Bhutan and... and fortunately, the rest of the packages have fans.
Therefore, if you are sure of the strength of the chimney coming out of the house, then you can be sure of the exit of smoke.

The final point is that there are three safety steps to prevent the package from bursting due to high heat

Flame cut command by heating NTC thermistor

The command to cut off the flame by the limit thermostat

Water exit due to high pressure by 3 bar safety valve

In other cases, the package is very safe

: What should we do to increase the life of your package??
Install an electrical protector. Electricity fluctuation sometimes causes damage to the package board. You can prevent this by installing a protector. Of course, this applies to all other wall packages and not only for Butan package.

Don't worry about package problems - Butan repairs in East Tehran

Try to check the possible signs of package failure by phone or in person if needed, so as not to cause further damage, perform the annual service of the package. The work process is that you call the Butan agency or a reliable repair center that you know, the Butan repairman will come to visit your package and perform tasks such as washing the secondary converter or charging the expansion source.

Try to choose the most technical, ethical and fair package repairer in Bhutan.

It is true that very honorable and skilled people are working in the package repair business, but unfortunately, we also see injustices in this profession. Because of this, finding a good and reliable repairman can be challenging.

My purpose in giving these tips is not to make you call us,
my purpose is for you to be careful in finding a good and reliable repairman,
to avoid problems and financial losses.

Here are some examples of the consequences of working with an abusive or unfair service provider:

Paying extra and unreasonable expenses,
performing unnecessary unethical repairs
and crushing your nerves,
not being accountable for the work done,
being impulsive and taking your time, and using low-quality parts.

I have always tried to introduce committed and ethical and technical repairmen for service.

Therefore, if anyone has a complaint about our repairman, leave a comment at the end of this article or anywhere on this site, or call the number that I put in the contact section of the site. Be sure that I will arrange the effect. Bhutan package repair service in East Tehran is available to all customers.

General points related to the temperature settings in the butane package

When using the wall package, always adjust the ambient temperature from the package and you are not allowed to adjust it with the radiator valve - in other words, when your house is heating up, do not close the radiator valve in any way, not even halfway, but the valves always Be completely open.

  And if you need to turn off the package, be sure to turn it off from the package, of course, if you really need to close or cut one of the radiators in half, there is no problem, do it - Butan repairs, East of Tehran

Do not set the hot water temperature to the highest level.
Some friends increase the temperature of water and radiator to the end. This is completely wrong.
Believe me, if the hot water is consumed in such a way that the human hand burns from the heat, no one will praise you for this work.
Adjust the temperature of the radiators so that the radiators have the desired heat.
Because by setting the temperature of water consumption and heating at the highest limit (maximum), it will be subjected to a lot of pressure
and the lifespan of the parts of the butane wall package, especially the pump and converter, will be greatly reduced.

One point:
the temperature of hot water and the temperature of the radiators in the wall package are set independently of each other,
which means you are allowed to set the temperature of the radiator to any desired value without affecting the temperature of the hot water consumed. And vice versa