10 Quick Tips For Kia Picanto Key Replacement

Author : Daugherty Persson | Published On : 21 May 2024

How to Fix a Dead Kia Picanto Key Fob

The Kia Picanto was built for the city. It swerves through traffic voids that bigger cars can't and slams through width limitations like they aren't even there. Despite its shabby appearance it is packed with plenty of features.

There are many reasons that the key fob that you have on your kia Picanto may not function. A dead battery is the most common reason.

Dead Coin Battery

The most common reason that a Kia Picanto key fob stops working is a dead battery. The key fob can show warning signs like fluctuating behavior or losing range before it eventually dies. It is recommended to replace your battery whenever you notice any of these symptoms before the battery has completely failed. Use a battery that has the same voltage, size, and specification as the original.

If the key fob still not working, you may need to take it to an authorized dealer. Only then can you ensure that the replacement key fob is compatible with your vehicle, and correctly programmed. Attempting to reprogram an ignition key fob without following the proper procedure could harm the chip inside and cause it to stop working.

A receiver module that has acquired a fault is another possibility. This could be the result of an unintentional chip damage or wear and tear as time passes. It can be difficult to recognize the signs of this problem, but it is important to look into the issue as soon as you can. If you are unable to use your key fob to unlock or lock the doors, or if even the spare isn't working and you are unable to lock or unlock the doors, contact a dealership or service center for assistance. They'll be able to diagnose the problem and repair it for you.

Faulty Chip


The key fob is equipped with an embedded chip that sends signals to the car's computer. If the chip gets corrupted it will not transmit the correct code, and the car's immobilizer system will be activated. This could be due many reasons. One of the causes is a battery that is not fully charged in the key fob. Another possibility is water damage. It is likely that the fob will cease to function if it gets wet.

A damaged chip could be the cause of why a Picanto fob doesn't turn on the engine. If you've replaced the battery, reprogrammed the fob and it still doesn’t function the circuit board might be damaged. If this is the case, you will require replacing it.

To open the fob, you must press a button that is located on the side of the fob. Once this is done, you will be able to take off the mechanical key. Then, follow the instructions below to replace the battery on the key fob. Be sure to use an alternative battery that has identical in size and voltage. The wrong battery can cause damage to the Fob. Press the lock button after replacing the battery. If it works, then you have a working Fob.

Faulty Receiver Module

Your key fob is subject to a lot of abuse and isn't a perfect piece of equipment. Over time, its buttons and battery contacts can become damaged and stop working properly. g28carkeys.co.uk to repair it using a few tools.

The fob needs to send a signal to a receiver inside your car in order for it to work. If the module is defective the fob won't be in a position to start or open the car. Resetting the fob is the first thing you can try.

This is accomplished by disconnecting the cable and letting the 12 volts battery drain completely. Then, connect the negative and positive cables in reverse order.

If the battery is in good shape and the fob doesn't have any water damage, the issue may be with the signal. This could be caused by many things including interference from nearby transmitters or objects that operate on the same frequency band as the Picanto's receiver.

Key fobs come with rubber seals which stop the electronic chip from becoming wet. However should they be submerged in water, the chips may be destroyed. This is the reason why it's essential to keep your key fob safe from water and only use a key fob with waterproof designs.

Programming errors

A Kia Picanto key fob is a convenient way to unlock and start your car. You can also use it to control the features of your vehicle. It is crucial to understand how to use the key fob correctly, especially when driving in bad weather or if you are unable to move. There are a lot of Kia Picanto key fob tricks to help you with this!

If your key fob suddenly stopped functioning it could be due to an issue with the internal chip. It is rare, but possible. It is best to consult a Kia dealer to pinpoint the issue.

You can also try to reset the Picanto keyfob. The procedure is easy and can be accomplished at home. The first step is removing the key fob. Connect the diagnostic tool underneath the dashboard to the OBDII connector and then start the engine. The diagnostic tool will ask for information regarding the Picanto. This includes the make model, model, and VIN.

You can also check for a dead battery. The clips made of metal in the key fob secure the battery and complete the circuit. If the retaining clip is not secure, it can disrupt the flow of electric current, resulting in an interruption in the function.